Home > Write Error > Write Error At 0000

Write Error At 0000

Contents

I'm using MicroCode Studio and EPIC Parallel Port Programmer. TheKannanmaster 8,593 views 9:08 android mtk baseband unknown problem 100% done - Duration: 13:59. I would have, but this is SOIC. No Life Poster Join Date: Nov 2009 Location: Estrancafe, South-Africa Age: 34 Posts: 7,615 Member: 1162626 Status: Offline Sonork: 100.1591727 QQ:2337938173 Thanks Meter: 7,038 Without Image Proved We get redirected here

Demon- 8th August 2006, 20:33At first it was about 6-12 inches of combined cables and traces, now 4-6 inches, no difference. Thia Apple 17,326 views 3:47 Repair dead boot gt-i8552 mtk 6572 - Duration: 3:29. محمد الرحيبي 5,973 views 3:29 how to flash any dead mtk android phone - Duration: 6:08. Results 1 to 8 of 8 Thread: Write Error on TOP853 programmer Thread Tools Show Printable Version Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode November 27th, 2011,08:11 Learn how Tapatalk'search and content recommendations can help you drive more traffic to your site.

Write Error Code 0000 Miracle Box

I just want to know, is it the programmer or Microchip quality control?? CPU: MT6572 SW:0000 Ver: CA01 Downloading Boot8 ... Getting them to do this, rather than pulling against each other, can make quite a difference to how your machine behaves, but most come out of their boxes inadequately set up It does happen--EPROMs have a fixed number of write cycles.

  • So now iam going to test these eproms.
  • I didn't really care what it programmed, as long as it went through the routine.
  • However, after repeated use, I now encounter the error message: "code programming error at 0000", which, on checking the readme text information, refers to power supply issues to an actual programmer,
  • I wasn't sure where the pull-up was supposed to go for PGC (what is 'normal connections'?) I tried a 4K7 pull-up on PGC with no difference anyways.
  • I say thank you for any help..
  • No Life Poster Join Date: Nov 2009 Location: Estrancafe, South-Africa Age: 34 Posts: 7,615 Member: 1162626 Status: Offline Sonork: 100.1591727 QQ:2337938173 Thanks Meter: 7,038 Check Vcom Usb Driver
  • Odd, I can program a 18F2550 on the same circuit over and over again without any problem.
  • Sign in to add this video to a playlist.

Insert USB cable. If so, the general rule of thumb is to stick the EPROM back into the eraser, then read it before writing to make sure that it contains nothing but FF bytes. Set DA USB VCOM Port (COM73) Writing(Nand/eMMC)... I don't think this is a configuration problem either 'cause I made sure to breadboard this circuit beforehand.

I've even tried to Erase manually first before Program, same error. Writing Mbr >>write Error Code: 0000 Trouble is, you have to edit every file for whatever PICs you are using. The solution is to modify the memory burning time factor, "ProgTime". You can always check the datasheet for your particular model.

EMMC Size: 0x00E7000000 Flash Type: EMMC INT/EXT RAM Size: 0x0+0x0 Waiting for USB Port... Sign in to make your opinion count. Search Search Forums Show Threads Show Posts Advanced Search Find All Thanked Posts Go to Page... Registration is fast, simple and absolutely free so please - Click to REGISTER!

Writing Mbr >>write Error Code: 0000

Then i get the write error.. If it's the parrallel, I saw kinda patch about XP printer polling blah blah... Write Error Code 0000 Miracle Box But realize this is the first time iam working with a eprom programmer device. Miracle Box Boot Data Error Power Off Phone , Remove Battery, Insert Battery Back 2.

Learn how Tapatalk'search and content recommendations can help you drive more traffic to your site. http://itechnologysolutionsllc.com/write-error/write-error-log-in-net.php In some cases Required Hold BootKey 3. Ed Kribbs- 29th October 2009, 16:37I had the same problem using 16F688 and 16F876. The first one i tried programming is programmed till 0170.. Gsm Forum

Totally wild guess, could this have anything to do with a write-protected chip? Thereafter the length of the few wires can also be optimized for proper functioning of the programmer. No, no flowers please, and not for me in any case Reply With Quote Quick Navigation Vintage Computer Programming Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums useful reference The first write went well and any further write is refused?

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. This can also occur if you haven't completely erased an EPROM (I'm assuming that you're trying to write one). Loading...

However, given the fact that you have some success with your PICs leads me to suspect that there is something 'marginal' in your setup.

shahidali55- 7th May 2012, 17:09Hi miragabe, In most programmers the MCLR pin will go to about 13 volts only during programming (for just a few seconds after clicking the program button). CPU: MT6572 SW:0000 Ver: CA01 Downloading Boot8 ... Like I said, 90% program with no problems. Team Hovatek 2,571 views 9:28 Loading more suggestions...

Or the device may need to be erased before reprogramming. MAYBE a programmer problem. If this works, then your programmer does not provide VPP before VDD during programming. this page Does anyone know of a good low-cost commercial programmer that can program all of the Pics?

They seemed to top at 12.9V on MCLR. Up next How To Removal Virus SexyPet Tools Android Phone with Miracle Box​ - Duration: 3:47. Connected to Phone. I'll try soldering PGC/PGD real close to the PIC and see if the length of the leads (along with trace length) is at fault.

I am a little confused though.

Follow us