Home > Winsock Error > Winsock Error 10060 Wsaetimedout

Winsock Error 10060 Wsaetimedout

Contents

See HOST_NOT_FOUND for details.WSANO_RECOVERY (11003) Non-Recoverable errors: FORMERR, REFUSED, NOTIMP Windows Sockets specification notes the domain name system (DNS) errors 'FORMERR, REFUSED, and & NOTIMP. COMMAND:> LIST STATUS:> Connecting ftp data socket xxx.xx.xxx.xx:xxxx... The most likely causes for Winsock timeouts include server overloading and network congestion. Do not set non-zero timeout on non-blocking sockets to avoid this ambiguity (see Chapter 9 for more information). Source

Any function that takes a socket as an input parameter--except close socket()--could potentially fail with this error. Last modified: 2012-01-25 DameWare Home | Product History | Community | Sales | Resellers | Contact Us Article - #300060 Support Home | Product Information Search for: WSAEALREADY 10037 Operation already in progress. WSAENOTCONN 10057 Socket is not connected.

Winsock Error 10061

WSAEBADF 10009 File handle is not valid. WinSock functions: socket() See also: WSAESOCKTNOSUPPORT WSAEPROTOTYPE (10041) Protocol wrong type for socket. WSAENETUNREACH 10051 Network is unreachable.

  • See also: WSAECONNABORTED, WSAENETRESET, WSAETIMEDOUT WSAEDESTADDRREQ (10039) Destination address required.
  • The call has been canceled.
  • WSAEBADF (10009) Bad file descriptor.
  • This can help you (or your support staff) to zero-in on what's wrong when your application runs into a problem.
  • WinSock functions: listen(), FD_CONNECT Additional functions: connect(), sendto() WSAELOOP (10062) Too many levels of symbolic links.
  • The Windows Sockets API does not have analogs for the Berkeley perror() and herror() functions that take the error value as input, and output the (short) text of each error value
  • Join group Get this RSS feed Home Forum Blog Wikis Files Members Table of Contents Knowledge Base Silk Performer 9.5 reports WebPageForm(WebEngine: 100 - Uncompressing content failed., internal error-code: -3) '0'
  • This is what occurs in Berkeley Sockets.

WinSock functions: WSAESHUTDOWN (10058) Cannot send after socket shutdown. WSAEHOSTUNREACH 10065 No route to host. The behavior may vary: some WinSocks might complete in background, and others may require another call to closesocket to complete. Socket Error 10054 WinSock description: Same as Berkeley.

WSAETIMEDOUT 10060 Connection timed out. Socket Error 10061 Connection Refused WSAEHOSTUNREACH (10065) No Route to Host A socket operation was attempted to an unreachable host. If an application sends a UDP packet to a host/port that does not have a datagram socket "listening," the network system may respond by sending back an ICMP Port Unreachable packet http://support.dameware.com/kb/article.aspx?ID=300060 The file handle reference is no longer available.

WSA_NOT_ENOUGH_MEMORY 8 Insufficient memory available. Socket Error 10061 Connection Refused Windows 7 The v1.1 WinSock specification doesn't list any errors for these functions. Berkeley description: A connection abort was caused internal to your host machine. WinSock description: Same as Berkeley, except WinSock doesn't support the sendmsg() function, and some WinSock implementations are not so strict as to require an application with a datagram socket to "disconnect"--by

Socket Error 10061 Connection Refused

Users should check: That the appropriate Windows Sockets DLL file is in the current path. I deleted channel.ini but that didn't change anything. Winsock Error 10061 Additionally, when using the MRC software over VPN connections to connect to these remote machines, you also need to keep in mind that the VPN may actually assign your local machine What Is A Socket Error WSASYSNOTREADY 10091 Network subsystem is unavailable.

Unfortunately, to find out what these errors mean you need to contact that WinSock provider. this contact form An address incompatible with the requested protocol was used. For example, the error can occur when an attempt is made to read from a file that is not open, to open an existing read-only file for writing, or to open If the signal handler performs a normal return, the interrupted function call will seem to have returned the error condition. Winsock Error 10060 Mdaemon

First server is used' & 'Could not start session recording for server...' warnings returned at the start of a load test in Silk Performer when dynaTrace plugin is enabled 'Show TrueLog' If you are using a router, verify the router is up and running (check by pinging it and then ping an address outside of the router). WSASYSCALLFAILURE 10107 System call failure. http://itechnologysolutionsllc.com/winsock-error/winsock-10060-error.php The following list describes the possible error codes returned by the WSAGetLastError function.

WSAEALREADY (10037) Operation already in progress An operation was attempted on a non-blocking object that already had an operation in progress.WinSock description: WSAEALREADY means that the asynchronous operation you attempted to How To Fix Error Code 10060 No such host is known. do you know any way i can do it manualy or have anyone used this program to know if it really works and is not a spam.

WSAEADDRINUSE (10048) Address already in use.

Berkeley description: The system detected an invalid address in attempting to use an argument of a call. Too many open sockets. Some WinSock implementation use these errors inappropriately, but they have a particular meaning. Winsock Error Code 10061 Exchange 2013 Berkeley description: A socket operation failed because the destination host was down.

Please check the URL to ensure that the path is correct. This is not a software error, another type of name server request may be successful. It can occur if you're trying to run too many applications (of any kind) simultaneously on your machine. http://itechnologysolutionsllc.com/winsock-error/winsock-error-10060.php WSAEADDRINUSE (10048) Address already in use Only one usage of each address is normally permitted.

The Windows Sockets implementation documentation to be sure all necessary components are currently installed and configured correctly. An invalid or inconsistent flowspec was found in the QoS provider-specific buffer. The specified socket parameter refers to a file, not a socket. This is not a temporary error.

if you could give me a step by step process i'll sure do it. 07-28-2007, 08:07 AM #11 TheMatt TSF Enthusiast Join Date: May 2006 Location: Boston Some implementations also return this error if sendto is called on a connected SOCK_DGRAM socket (for SOCK_STREAM sockets, the to parameter in sendto is ignored) although other implementations treat this as For protocols and services resolution, it means the respective database wasn't located. WSAECONNRESET (10054) Connection reset by peer A connection was forcibly closed by a peer.

You cannot mix and match (WINSOCK DLLs must be supplied by the same vendor that provided your underlying protocol stack). By calling shutdown a partial close of a socket is requested, which is a signal that sending or receiving, or both have been discontinued.

Follow us