Home > Socket Error > Winsock Error 10057 Socket Is Not Currently Connected

Winsock Error 10057 Socket Is Not Currently Connected

Contents

Typically, only one usage of each socket address (protocol/IP address/port) is permitted. WSA_QOS_EFILTERTYPE 11020 Invalid QoS filter type. Too many references to some kernel object. This normally results if the peer program on the remote host is suddenly stopped, the host is rebooted, or the remote host used a "hard close" (see setsockopt for more information Source

A completion indication will be given at a later time when the operation has been completed.WSA_IO_INCOMPLETE (OS dependent)Overlapped I/O event object not in signaled state.The program has tried to determine the Covered by US Patent. An invalid QoS filter type was used. Most attackers fall into one of four categories, each with their own favored tactics, techniques, and procedures. https://msdn.microsoft.com/en-us/library/windows/desktop/ms740668(v=vs.85).aspx

Socket Error 10038

For more information, see topics on Network Address and Network Port, at ms-help://MS.HIS.2010/HIS2010/html/9e844d5c-d177-41d4-9489-2a29b919efcf.htm#tcpip3.NAWSAEHOSTUNREACH08S0110065Message: A TCPIP socket error has occurred (10060): The connection has been dropped because of a network failure or WSAEINVALIDPROCTABLE 10104 Procedure call table is invalid. If not, check with your Winsock vendor to see if they have a newer Winsock available. From other articles I've read the status change is a a result of Winsock being asked to do something, yet is busy and as a result of the socket being a

  1. I'm using: -asynchronous socket -TCP -s is a valid socket -i'v looped RequestInfo for several passes but nothing changes -select() returns 0 -datasize returns -1 with errcode 10057 THANK YOU !!!
  2. A message sent on a datagram socket was larger than the internal message buffer or some other network limit, or the buffer used to receive a datagram was smaller than the
  3. A call to the WSALookupServiceEnd function was made while this call was still processing.
  4. If so, then the application might have had a problem resolving the name.

A server has attempted to handle an NFS request by generating a request to another NFS server, which is not allowed.WSAHOST_NOT_FOUND (11001) Host not found The name you have used is Cannot remove a directory that is not empty. next, connection pool. Socket Error 10049 At least one QoS send path has arrived.

Do you have the Winsock DLL that supports the version of the Winsock specification required by the application? Socket Error Codes Linux WSA_QOS_EOBJLENGTH 11022 Invalid QoS object length. This error signifies that an attempt was made to access a file (or, in some cases, a directory) in a way that is incompatible with the file's attributes. https://msdn.microsoft.com/en-us/library/gg164819(v=bts.70).aspx WSAVERNOTSUPPORTED 10092 Winsock.dll version out of range.

WSAEPFNOSUPPORT 10046 Protocol family not supported. Socket Error 11004 you can also create the threads only as needed, but that can be a little complicated, so I would leave it to when you have more free time - connection pooling. A general QoS error. The service provider procedure call table is invalid.

Socket Error Codes Linux

Is there a "weighting" involved with Sitecore.ContentSearch.SearchTypes.SearchResultItem? Only after a minute or so do the first errors pop-up. Socket Error 10038 This has worked well in various other threaded applications I've written, it's just now I'm running into problems. Socket Error 10054 Connection Reset By Peer For more information on command and data type limits, see topic on Data Type Mappings, at ms-help://MS.HIS.2010/HIS2010/html/cca7e3a6-6160-48ca-89d2-90318900807f.htm.NAWSAEFAULT08S0110014Message: A TCPIP socket error has occurred (10043): The specified protocol is not supported. Reason: The

that way you can keep the connections open and re-use them (you will need a small amount of synchronization here twhen getting an open connection. this contact form You cannot send or receive data over the server socket since it's not connected to anything. I tried reversing this so that the WSA... WSA_QOS_GENERIC_ERROR 11015 QoS generic error. Socket Error 10053

The requested service provider could not be loaded or initialized. WSAEWOULDBLOCK (10035) Operation would blockThis is a temporary condition and later calls to the same routine may complete normally. A request to send or receive data was disallowed because the socket had already been shut down in that direction with a previous shutdown call. have a peek here At the time of SendStr, if the state is wsConnecting I've tried waiting around a bit (calling the ProcessMessages of the Socket object) to only proceed if it becomes connected.

Too many open sockets. Winsock Error 10054 Fix WSASERVICE_NOT_FOUND 10108 Service not found. Not implemented: Name server does not perform specified operation.

WSA_QOS_POLICY_FAILURE 11011 QoS policy failure.

The file handle reference is no longer available. Privacy Policy Site Map Support Terms of Use It appears that you have Javascript disabled or your browser does not support Javascript. You can monitor available memory with Program Manager's 'Help/About...' command. Windows Socket Error Windows 10 It can occur if you're trying to run too many applications (of any kind) simultaneously on your machine.

A case like this could easily cost hundreds of thousands of dollars. It also has a specific meaning for setsockopt(). An existing connection was forcibly closed by the remote host. Check This Out The requested protocol has not been configured into the system, or no implementation for it exists.

if you can't find anything like that, then try to follow the flow of the execution of a job and isolate the places where the socket could get disconnected: for example This is a generic error code, returned under various conditions.

Follow us