Home > Socket Error > Winsock Connect Error 10065

Winsock Connect Error 10065

Contents

If it persists, exit Windows or reboot your machine to remedy the problem. Note that this error occurs rarely, because a Winsock implementation cannot reliably detect hardware problems.WSAENETUNREACH (10051) Network is unreachable A socket operation was attempted to an unreachable network. Verify that your subnet mask is setup properly. Join group Get this RSS feed Home Forum Blog Wikis Files Members Table of Contents Knowledge Base Silk Performer 9.5 reports WebPageForm(WebEngine: 100 - Uncompressing content failed., internal error-code: -3) '0' Source

This may indicate the file was deleted on the NFS server or some other catastrophic event occurred. The ICMP message means that the router can't forward the IP datagram, possibly because it didn't get a response to the ARP request (which might mean the destination host is down).WSAENOTEMPTY This is not a temporary error. This error means that a socket operation was attempted to an unreachable host.

Socket Error 10061 Connection Refused

Try pinging the address. (See Troubleshooting Tips for details.) If you are using a router, verify the router is up and running (check by pinging it and then ping an address This error indicates a shortage of resources on your system. The error can also occur in an attempt to rename a file or directory or to remove an existing directory.WSAEFAULT (10014) Bad addressThe system detected an invalid address in attempting to A retry at some time later may be successful.

So if for any reason the software is unable to communicate with the Service Control Manager on the remote machine (Access Denied, ports blocked, etc..), then the software will not be This error apparently also takes the place of WSAEPFNOSUPPORT (which means 'protocol family not supported'), since that error is not listed for socket. Typically though, Winsock generates this error when it receives a 'host unreachable' ICMP message from a router. Socket Error 10061 Connection Refused Windows 7 This means another type of request to the name server will result in an answer.

Verify that the destination host name or IP address is correct and try again later. Winsock Error 10061 Home » Borland » Test » Silk Performer » Silk Performer Knowledge Base » Why do I get the error "Winsock 10065 - no route to host" on replay and how WSANOTINITIALISED (10093) Successful WSASTARTUP not yet performed Either your application hasn't called WSAStartup, or WSAStartup failed. http://community.microfocus.com/borland/test/silk_performer_-_application_performance_testing/w/knowledge_base/8845.why-do-i-get-the-error-winsock-10065-no-route-to-host-on-replay-and-how-can-i-troubleshoot-it.aspx A socket already has a type (a protocol), and each sockaddr structure has an address family field to define its format.

The most common cause is an incorrectly configured server, full server, or incorrect Port specified by the client. Error Code 10060 Socket Connection Failed No HTML please.                           12345678910 Average rating: 8.0 out of 10. 303 people have rated this article. Switch to the opposite data connection type (PASV or PORT) under Site Settings > Type tab. This helps avoid unnecessary reduction in server performance.

Winsock Error 10061

You cannot mix and match. (WINSOCK DLLs must be supplied by the same vendor that provided your underlying protocol stack).You cannot use more than one Winsock implementation simultaneously.If you have more http://forums.dameware.com/viewtopic.php?f=9&t=1241 Usually, the manufacturer of the device or software has specific instructions available on their Web site. Socket Error 10061 Connection Refused A server has attempted to handle an NFS request by generating a request to another NFS server, which is not allowed.WSAHOST_NOT_FOUND (11001) Host not found The name you have used is 10060 Socket Error Possible reasons: Wrong version of perfdotnetfw.dll, unhandled exception in constructor or insufficient permissions!". "DotNetCallMethod(DOTNET: 15 - Exception has been logged!, Only one element allowed per config file and if present

The Winsock implementation will not allow you to send after this. http://itechnologysolutionsllc.com/socket-error/winsock-error-10065-no-route.php If you continue to receive the same error after insuring ports 20 and 21 are open, please contact the administrator of the site where you are trying to connect. But from what I'm told, filtering between VLANs does not work this way (the same way that firewalls do), and it's more like an application-layer firewall where you must define specific Although the Mini Remote Control program only requires a single TCP port (default is TCP 6129) for communication with the MRC Client Agent on the remote machine, other ports & protocols Winsock Error 10060

Additionally, when using the MRC software over VPN connections to connect to these remote machines, you also need to keep in mind that the VPN may actually assign your local machine Silk Performer Improve customer satisfaction by delivering reliable, high performing applications. Blocking on outbound connections is not typically done in Firewalls because then basically nothing would work. http://itechnologysolutionsllc.com/socket-error/winsock-10065-error.php Do you have the Winsock DLL that supports the version of the Winsock specification required by the application?

g., Norton Internet Security) is blocking access. How To Fix Error Code 10060 If the hostname resolution uses a local host table, it is possible you resolved to an obsolete address. It only disconnects if the client and the server have not communicated for a specific period of time as defined by the server administrator.

Check your Winsock implementation documentation to be sure all necessary components are currently installed and configured correctly.

Consult the documentation or help file for your specific firewall or antivirus software product for instructions. Please consult the documentation or help file for your specific firewall or antivirus software product for further instructions. WSAEHOSTUNREACH (10065) No Route to Host A socket operation was attempted to an unreachable host. Socket Error 10060 Connection Timed Out By default, it's currently set to Socket Logon Timeout=90000 (in milliseconds), so you can try doubling that value to start out.

TCP/IP scenario: In BSD-compatible implementations, the local network system generates this error if there isn't a default route configured. Otherwise the connection will timeout with a Winsock 10060 error. For example, you can try to ping the server(s). http://itechnologysolutionsllc.com/socket-error/winsock-error-10065-no.php Check your subnet mask.

The only function that takes these two explicit parameters is socket.WSAENOPROTOOPT (10042) Bad protocol option A bad option or level was specified in a getsockopt(2) or setsockopt(2) call. The Windows Sockets API provides access to 'low-level' APIs (like the transport protocols TCP and UDP), so this error is not relevant to Winsock. WSAEISCONN (10056) Socket is already connected A connect request was made on an already connected socket; or, a sendto or sendmsg() request on a connected socket specified a destination when already If you are using a name server(s), check whether the server host(s) are up.

If the signal handler performs a normal return, the interrupted function call will seem to have returned the error condition. Try the following: Check that the WINSOCK.DLL file is in the current path. An asynchronous signal (such as SIGINT or SIGQUIT) was caught by the process during the execution of an interruptible function. Do you have a router configured?

Typically, though, Winsock generates WSAENETUNREACH when it receives a "host unreachable" ICMP message from a router instead of WSAEHOSTUNREACH. So, for example, if a Winsock implementation doesn't support SOCK_RAW with IPPROTO_IP (or any other protocol), then the socket call would fail with WSAEPROTONOSUPPORT (however, if it doesn't support SOCK_RAW at It may also indicate you are not closing the applications properly. Once the Mirror Driver has been installed on the remote machine, simply enable the "Use MRC Mirror Driver (if available)" checkbox on the Remote Connect dialog before you click on Connect.

But make note this does not open the ports required to remotely install, remove, start, or stop the MRC Client Agent Service, only the port specified to use for communication. Need Help? Example: ping server1.demo.com If you can successfully ping the server then it may be a port issue, please try to telnet to the server on the port your client is connecting Check Maintain connection at "idle" under Preferences > Advanced.

A function fails with WSAEAFNOSUPPORT if the address family referenced in sockaddr is not compatible with the referenced socket's protocol.

Follow us