Home > Socket Error > Winsock Bind Error=10050

Winsock Bind Error=10050


WinSock description: Same as Berkeley. Note that this error is returned by the operating system, so the error number may change in future releases of Windows. An application attempts to use an event object, but the specified handle is not valid. Berkeley description: A connection was forcibly closed by a peer. Source

If you are using a name server(s), check whether the server host(s) are up. So, for example, you can expect this error if a WinSock implementation doesn't support socket type SOCK_RAW within the Internet address family (AF_INET). A QoS error occurred due to lack of resources. It is normal for WSAEWOULDBLOCK to be reported as the result from calling connect on a nonblocking SOCK_STREAM socket, since some time must elapse for the connection to be established. https://msdn.microsoft.com/en-us/library/windows/desktop/ms740668(v=vs.85).aspx

Socket Error 10054

As you see WSAGetLastError() is an essential function to use, if you want to know why your application might be failing. Usually this occurs when a socket descriptor to a socket that cannot support this operation is trying to accept a connection on a datagram socket. In WinSock it means a blocking operation was interrupted by a call to WSACancelBlockingCall. Developer suggestions: to make your application more portable: with datagram sockets don't use connect() and sendto() on the same datagram socket in an application, and always "disconnect" before calling connect() more

  1. Networking activity on the local host has not been initiated.
  2. If this tends to occur after running certain applications for a while, it might be a symptom of an application that doesn't return system resources (like memory) properly.
  3. For example, you cannot use the ARPA Internet UDP protocol with type SOCK_STREAM.
  4. If you used a hostname, did it resolve to the correct address?

WSAEINTR 10004 Interrupted function call. WSAEACCES 10013 Permission denied. When you get this error it usually means the system was trying to send a message that was larger than the receiving system would accept OR the receiving system had a Socket Error 10049 WinSock functions: WSAEWOULDBLOCK (10035) Resource temporarily unavailable.

WSAEPFNOSUPPORT 10046 Protocol family not supported. If you used a hostname, did it resolve to the correct address? A socket operation encountered a dead host. http://support.dameware.com/kb/article.aspx?ID=300058 Run two instances of the server (with our updated code) and see what happens.

Developer suggestions: Since there're only one corresponding protocol for each of the datagram and datastream socket types in the Internet address family, you should simply leave the value in the protocol Socket Error 11004 The software caused a connection abort because there is no space on the socket's queue and the socket cannot receive further connections.WinSock description: The error can occur when the local network Note that this error occurs rarely since a WinSock implementation cannot reliably detect hardware problems. Once we are happy that Winsock has initialized correctly, we can now use a handy function to address any further failures.

Socket Error Codes Linux

TCP, UDP, ICMP, ARP, DNS) that typically causes the error. http://www.sockets.com/err_lst1.htm Do you have a router configured? Socket Error 10054 copies what it can into your buffer) and fails the function. Socket Error 10053 TCP/IP scenario: A connection will timeout if the local system doesn't receive an (ACK)nowledgement for data sent.

WinSock functions: Additional functions: For Berkeley compatibility, the socket() function should fail with this error if an unsupported address family is requested. this contact form This will verify that the destination network is functioning. WSAEADDRNOTAVAIL (10049) Can't assign requested address Normally results from an attempt to create a socket with an address not on this machine. User suggestions: Some network systems have commands to report statistics. Socket Error 10054 Connection Reset By Peer

On the server end, you could use a network system utility similar to BSD's "netstat -a" command to check that your server is running, and listening on the right port number. In this case, it might be possible to check the count of TCP RST packets received, or ICMP Port Unreachable packets. WSAHOST_NOT_FOUND for details. http://itechnologysolutionsllc.com/socket-error/winsock-error-code-10050.php Check your subnet mask.

WinSock functions: getpeername(), recv(), recvfrom(), send(), sendto(), setsockopt(), shutdown(), FD_CONNECT See also: WSAECONNABORTED, WSAECONNRESET, WSAENETRESET, WSAETIMEDOUT WSAENOTEMPTY (10066) Directory not empty. Winsock Error 10054 Fix No HTML please.                           12345678910 Average rating: 5.1 out of 10. 64 people have rated this article. An unrecognized object was found in the QoS provider-specific buffer.

WSADATA WsaDat; int nResult=WSAStartup(MAKEWORD(2,2),&WsaDat); if(nResult!=0) { std::cout<<"WSA Initialization failed: "<

Check whether you have a router configured in your network system (your WinSock implementation). An MX record is returned but no A record—indicating the host itself exists, but is not directly reachable. For protocol and services resolution, the name or number was not found in the respective database. Socket Error 10061 Connection Refused A server has attempted to handle an NFS request by generating a request to another NFS server, which is not allowed.WSAHOST_NOT_FOUND (11001) Host not found The name you have used is

The file handle reference is no longer available. Detailed description: SO_BROADCAST is not supported on sockets of type SOCK_STREAM. If it persists, exit Windows or reboot your machine to remedy the problem. Check This Out However, there's little distinction between WSAEALREADY and WSAEINVAL since a WinSock DLL cannot tell the difference between an asynchronous operation that has been cancelled and one that was never valid.

Check the destination address you are using. WinSock description: Same as Berkeley. WSAEMSGSIZE (10040) Message too long.

Follow us