Winsock 10065 Error
Too many references to some kernel object. For protocols and services resolution, it means the respective database wasn't located. Silk Performer Improve customer satisfaction by delivering reliable, high performing applications. A socket operation was attempted to an unreachable network. http://itechnologysolutionsllc.com/socket-error/winsock-error-10065-no.php
An invalid or inconsistent flowspec was found in the QOS structure. If a server name was used, verify it resolves to the correct address. WSAENOBUFS 10055 No buffer space available. Based on the original by Alex Kunadze. http://community.microfocus.com/borland/test/silk_performer_-_application_performance_testing/w/knowledge_base/8845.why-do-i-get-the-error-winsock-10065-no-route-to-host-on-replay-and-how-can-i-troubleshoot-it.aspx
Socket Error 10061 Connection Refused
Try that simple task first to see if it fixes the error code problem. A QoS error occurred due to lack of resources. WSAEPROCLIM 10067 Too many processes. For information, see the Handling Winsock Errors topic.
- Winsock only allows a single blocking operation to be outstanding per task (or thread), and if you make any other function call (whether or not it references that or any other
- WSAENETDOWN (10050) Network is down A socket operation encountered a dead network.
- Some error codes defined in the Winsock2.h header file are not returned from any function.
- It only disconnects if the client and the server have not communicated for a specific period of time as defined by the server administrator.
- If you don't have the proper subnet mask, your network system may treat a local address as a remote address (so it forwards addresses on the local subnet to the router,
It is a nonfatal error, and the operation should be retried later. For example, you cannot use the ARPA Internet UDP protocol with type SOCK_STREAM. First server is used' & 'Could not start session recording for server...' warnings returned at the start of a load test in Silk Performer when dynaTrace plugin is enabled 'Show TrueLog' Winsock Error 10060 back to top dameware.com The Official DameWare Development Community Forum Skip to content Advanced search Board index Change font size FAQ Register Login Information The requested topic does not exist.
Either can block the ports needed to make a successful FTP connection to the remote server. What Is A Socket Error ERROR:> Failed to establish data socket. WSA_QOS_EUNKOWNPSOBJ 11024 Unrecognized QoS object. WSASERVICE_NOT_FOUND 10108 Service not found.
It means that there is a blocking operation outstanding.It is also possible that Winsock might return this error after an application calls connect a second time on a non-blocking socket while Socket Error 10053 Memory mismanagement. No connection could be made because the target computer actively refused it. An invalid QoS provider-specific buffer.
What Is A Socket Error
WSAEAFNOSUPPORT 10047 Address family not supported by protocol family. https://groups.google.com/d/topic/comp.sys.ibm.as400.misc/3hjZu5g-16Y Most common examples include: 1) incomplete software installation; 2) incomplete software uninstallation; 3) improperly deleted hardware drivers, and 4) improperly deleted software applications. Socket Error 10061 Connection Refused Verify that the destination server name or IP address is correct Verify that the connection port number is correct (under Site Settings > Type tab). Winsock Error 10061 All rights reserved.
This would occur if WinSock aborts an established connection after data retransmission fails (receiver never acknowledges data sent on a datastream socket). this contact form A message sent on a datagram socket was larger than the internal message buffer or some other network limit, or the buffer used to receive a datagram was smaller than the WSAHOST_NOT_FOUND for details.WSANO_ADDRESS (11004)* No address, look for MX record The requested name is valid, but does not have an Internet IP address at the name server. For example, if a call to WaitForMultipleEvents fails or one of the registry functions fails trying to manipulate the protocol/namespace catalogs. Socket Error 10054
WSAEWOULDBLOCK (10035) Operation would blockThis is a temporary condition and later calls to the same routine may complete normally. Also, Winsock Error 10065 No Route To Host errors are very common during PC restarts that immediately follow a previous improper shutdown and recent virus or malware infection recovery. Possible reasons: Wrong version of perfdotnetfw.dll, unhandled exception in constructor or insufficient permissions!". "DotNetCallMethod(DOTNET: 15 - Exception has been logged!, Only one
WinSock description: The 'address' they refer to, typically refers to the local 'socket name', which is made up of the 3-tuple: protocol, port-number and IP address. Socket Error 10061 Connection Refused Windows 7 An unknown, invalid or unsupported option or level was specified in a getsockopt or setsockopt call. Login Register Login Username: Password: Lost Password?
Should you be particularly aquiring a challenge with gradual rebooting, you need to test the startup courses in your laptop or computer.
Check your Winsock implementation documentation to be sure all necessary components are currently installed and configured correctly. See also: Unable to connect to remote system Skip to content Easy Software Ltd Appointment Scheduling, Employee Scheduling, and HR Software Menu and widgets Search for: Pages Repairing your Computer Sitemap WSAEMSGSIZE 10040 Message too long. Socket Error 10061 Ppsspp Some invalid argument was supplied (for example, specifying an invalid level to the setsockopt function).
This error also could occur if an application opens and closes sockets often, but doesn't properly close the sockets (so it leaves them open, as 'orphans'). WSAEADDRNOTAVAIL (10049) Can't assign requested address Normally results from an attempt to create a socket with an address not on this machine. WSA_QOS_EPSFILTERSPEC 11028 Invalid QoS provider-specific filterspec. Check This Out Cannot translate a name.
We appreciate your feedback. It may also indicate you are not closing the applications properly. A request to send or receive data was disallowed because the socket had already been shut down in that direction with a previous shutdown call.