Home > Error Code > Whirlpool Gold Gas Range Error Codes

Whirlpool Gold Gas Range Error Codes

Contents

Check for conformal coating on serial communication pins between the machine controller and the motor controller. Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle. F21 LONG DRAIN If the drain time exceeds 8 minutes the water valves turn off. This should clear the unit of the excess detergent. 1. weblink

F34 UNLOAD INDICATION This failure is only for information and can be displayed in the error history during the Diagnostic Test. Repeat steps A and B for door switch. 3. Located on the bottom of the door latch assembly is a tear-drop shaped tab. 5. F05 - Water Temperature Sensor Error - Unplug and disconnect power to the unit and check all connections to the water temperature sensor, heating element and element relay.

Whirlpool Oven Fault Codes

Unplug washer or disconnect power. 3. This should have AC line voltage when the motor controller is powered. G Clears when oven temp drops below the runaway temp and the selector is off. Located on the bottom of the door latch assembly is a tear-drop shaped tab. 5.

  • Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab.
  • codes.
  • Replace is defective.
  • Bill Newberry 17,190 views 3:36 Checking an Oven Temperature Sensor - Duration: 3:58.
  • Check dispenser motor for powered rotations.
  • F28 SERIAL COMMUNICATION ERROR The communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly. 1.
  • Enter your model number for the best repair help results.
  • If you can’t look through it, exchange Steamer. 5.
  • The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit.

The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed. F32 PRESSURE SWITCH FAILURE If there is no electrical supply to the Pressure Switch from the CCU or if the Pressure Switch contacts are worn out, then a Pressure Switch Failure Press START to continue the cycle from the moment that power was lost. Whirlpool Top Load Washer Error Codes F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down.

Short circuit of Heater to Ground. Disconnect power for at least 30 seconds. 2. Make sure the drain pump is free from debris or foreign objects and then reconnect power and plug unit in.

Verify CCU operation by running a Diagnostic Test or any cycle. 6.

If not, replace the sensor. Whirlpool Oven Error Codes F5 This does not generate an error code beep. This error code may also be used if there is a disagreement between the motor and machine controllers on the state of the lid switch. BRANDS ERROR CODES FOR SOME COMMON U.S.

Whirlpool Range Error Code F9e0

F9 - Oven Door Lock Failure - Check door lock switches and wiring. https://www.whirlpool.com/product-help/error-code-on-the-range-or-built-in-oven-display/PH3756/ If failure remains, disconnect power and replace control. Whirlpool Oven Fault Codes The failure will be reset after running the Diagnostic Test Program. 1. Whirlpool Washing Machine Error Codes E1 Press 'Stop/Cancel' to clear the display.

Unplug washer or disconnect power. 2. have a peek at these guys Check Pressure Switch harness for continuity. 2. F3 Oven temperature sensor (RTD) open Replace Oven temperature sensor (RTD) F4 Oven temperature sensor (RTD) shorted Replace Oven temperature sensor (RTD) F5 Board failure Replace control board (also called ERC F63 TOTAL STEAMER FAILURE If this Failure is displayed, one or several vital values are out of range. Whirlpool Oven Error Codes E2 F3

As always, disconnect power on any control you're disassembling or assembling. Refer to the Continuity tests. Unplug washer or disconnect power. 2. check over here Check/clean drain pump filter of foreign objects. 5.

CE - Communication Error - Disconnect power and unplug unit. Whirlpool Top Load Washing Machine Error Codes If there is an error reading this data it will cause this error. Continue Shopping home Service & Support Product Help Return to Search Results Print No results were found.

Verify CCU operation by running a Diagnostic Test or any cycle. 3.

Reset the oven and see if that fixes it, and if not, replace the control board.For a lot of Whirlpool ovens, you have to replace the clock along with the control Check the drive system for any worn or failed components. 5. Unplug washer or disconnect power. 2. Whirlpool Oven Error Codes E6 F2 Verify CCU operation by running a Diagnostic Test or any cycle.

Press STOP/CANCEL to clear the display. If you have this problem and your sensor passes the test, do NOT order a new ERC until putting the oven back together and giving it a try. During the Cleaning Cycle was load detected inside the drum and Cleaning Cycle was interrupted by indicating “rL” to User. this content Press STOP/CANCEL to clear the display.

This should clear the unit of the excess detergent. • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain OVEN ELEMENT RELAYS Usually a "high oven temperature" code means the temperature sensor or ERC is bad. F30 DISPENSER SYSTEM ERROR When the dispenser motor cannot be driven to its proper position. 1. F7 - E1 Common switch wire is defective Common wire (+5VDC) to latch switch, and to door switch is shorted to chassis ground or neutral.

Potential Causes • Door Lock Mechanism broken. • Check Door Lock/Switch Assembly for foreign objects • Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) • Replace probe if all else checks out ok. Audible clicks will be heard from the switch. That's a fine strategy, but when the machine has a problem, it can make diagnosing and finding the correct replacement part something of a task.

The door should now be unlocked. Check that NTC resistance of the Steamer is in range between 170 kΩ and 300 Ω, refer to Temperature Sensor table on page 10. Possible Causes/Procedure Door lock mechanism is broken or removed from door. Correctly diagnosing a fault code in a Sears / Kenmore oven starts with identifying who made the oven, using the first three digits of the model number.

Replace control board (clock). The washer does not flash "PF" when it is first plugged in. Check the inlet valve and pressure switch for proper shut off and operation. Check the drive system for any worn or failed components. 4.

Replace Central Control Unit if drum is not moving F71 USER INTERFACE HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the User Interface Ft. The wires should be to the left when facing the MCU connectors. 9. F27 OVERFLOW CONDITION If the overflow contact on the pressure switch is closed for more than 60 seconds, an Overflow Condition occurs.

F1-E2 - UL A/D Error(s) - Disconnect power for at least 30 seconds and then reconnect. Have you ever purchased from PartSelect.com before? The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed. Check MCU by looking for operations of the drive motor and check drive motor for powered rotations.

Follow us