Home > Error Code > Whirlpool F1 Error Oven

Whirlpool F1 Error Oven

Contents

Select the 'cancel' function and wait 60 seconds. So if you've misdiagnosed a problem and bought a keypad when the problem was a circuit board, you're now the not-so-proud owner of an expensive keypad that is of no use The oven will come on and heat up to about 150 to 170 and turn off. Ld - Long Drain - This error code will appear if unit takes longer than 5 minutes to pump out water to the point where the pressure switch resets. weblink

Replace failed component. Try unplugging unit for two minutes to see if that fixes error. Some common causes of "CE" errors include: • Conformal coating on serial communications pins between the machine controller and motor controller. Where an error code tells you to check the ERC in a double oven, make sure you check both boards.

Whirlpool Range Error Code F9e0

Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab. Press STOP/CANCEL to clear the display. Sensor resistance should be 1K to 1.1K @ room temperature. DiscoverC Home Decor & Repair Crafts Food & Drink Garden Entertaining Fashion & Beauty Holidays Tech Personal Finance Cars Pets Legal Life's Moments Retirement Investing for Today Honest Hacks U Search

LF - Long Fill - If the water fill time exceeds ten minutes, the water valves will be shut off and this error code will display. The Whirlpool Cabrio Washer's Error Code F1 The Whirlpool Cabrio Washer's Error Code F1. ... Up next Range Oven F1 Error Repaired - Duration: 11:02. Whirlpool Microwave Error Codes Replace switch if defective. 5.

Open the lid or press 'Stop/Cancel' to clear display. Whirlpool Washing Machine Error Codes E1 Press STOP/CANCEL to clear the display. ^ top CE Communications error If there is any breakdown in communication between the machine controller and the motor controller, "CE" flashes and the unit Find Parts Whirlpool Duet Front Loading Automatic Washer Fault Codes Failure Code Fault Code Description Solution FH No water detected entering machine or Pressure switch trip not detected. pop over to these guys If connections are ok, then check individual switches as outlined for the F5 error code.

Top 6 Reasons Electric Oven Won’t Heat? Whirlpool Top Load Washing Machine Error Codes F9 - Oven Door Lock Failure - Check door lock switches and wiring. Verify Central Control Unit (CCU) is operating properly by running a diagnostic test or any cycle. Select 'cancel' and observe for one minute for errors.

  1. Select the 'cancel' function and wait 60 seconds.
  2. I do have a dvom and test lights for testing.
  3. All rights reserved.
  4. Replace door switch.
  5. The following lists the manufacturers of these machines, though it should not be considered exhaustive: 103 Roper 106 Whirlpool 110 Whirlpool 155 Roper 174 Caloric 198 Whirlpool 253 Gibson 362 GE
  6. Press STOP/CANCEL to clear the display.
  7. This should have AC line voltage when the motor controller is powered.
  8. For this reason, I caution you: IF YOU ARE NOT SURE OF YOUR DIAGNOSIS, CALL A QUALIFIED, FACTORY-AUTHORIZED TECHNICIAN to diagnose and repair your oven.

Whirlpool Washing Machine Error Codes E1

F02 - Long Drain (Drain Exceeds 8 Minutes) - Select 'cancel' twice to clear error code.

I also checked continuity of the 2 purple wires from the temp sensor to the erc and they have 0.00 resistance, not a bad wire or wiring problem to the erc. Whirlpool Range Error Code F9e0 If this happens, replace oven control (also called clock or ERC). 2. Whirlpool Top Load Washer Error Codes Press and HOLD start to continue the cycle, or press off/pause to clear display.

OR Press STOP/CANCEL to clear the display and completely cancel the cycle. have a peek at these guys F1-E9 - Stack Overflow - Disconnect power for at least 30 seconds and then reconnect. Whirpool Calypso Automatic Washer Fault Codes PF - Power Failure - PF error code indicates a power failure during the dryer's cycle. Unplug the unit to service. Whirlpool Oven Error Codes E2 F3

This does not generate an error code beep. Verify that the inlet valve is operational. Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. check over here The door may now be opened. ^ top Find Parts Whirlpool Duet Front Loading Gas and Electric Dryer Fault Codes Failure Code Fault Code Description Solution PF Power failure "PF" flashes

Check drain pump and pressure switch and verify CCU operation by running a diagnostic test or any cycle. Whirlpool Oven Temperature Sensor G Clears when oven temp drops below the runaway temp and the selector is off. LS - Lid Switch Error - This error will occur if unit cannot detect the lid switch opening or closing.

Loading...

Close the lid and press 'Start' to continue. An F1 reading can also indicate a safety flip-flop or a shorted keypad, which will require that you replace the board or the keypad. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). Whirlpool Accubake Oven Error Codes FL Flood condition "FL" flashes if any overfill condition occurs.

F2-E0 - Shorted Touch Pad (Keypad) - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Reply With Quote December 15th, 2007,02:39 AM #5 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location McMullen Valley, Arizona Posts 79,885 I've LS - Lid Switch Error - This error will occur if unit cannot detect the lid switch opening or closing. this content Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).

I pulled the range away from the wall, took off the back access panel and found a wire that had burned up against the frame and was causing it to short Then plug it back in and see if the code clears. Check CCU is also operational by performing a diagnostic test or any cycle. Press CANCEL and observe for 1 minute to ensure operation is correct. 6.

Check wire harness connections between drive motor and Motor Control Unit (MCU), and between MCU and the Central Control Unit (CCU).

Follow us