Home > Error Code > Whirlpool Duet Washer Error Codes F 27

Whirlpool Duet Washer Error Codes F 27

Contents

Check wire harness connections to the door switch/lock unit and Central Control Unit (CCU). In fact, given the conditions that these washing machines have to work in— lots of vibration, moisture, humidity, heat, etc.— it’s amazing they work as well as they do. Plug in washer or reconnect power. 6. Perform Service Cycle to pair the UI and CCU SW. 2. weblink

The failure will reset after running the Diagnostic Test Program. 1. Push the door and check if it is completely closed. 2. Oops! D. http://www.shopyourway.com/questions/1087402

Whirlpool Duet F27 Error Code

Place a bucket or pan underneath it since you will get the water spilling out of there. By reading any content on this site you agree to AppliancePartsPros.com , Inc. Replace User Interface if drum is rotating. 4. F8 Board failure Replace control board (also called ERC or clock).

Good luck Oct 02, 2009 | Whirlpool Duet GHW9150P Front Load Washer 7 Answers F21 Error Code on Whirlpool Duet & Kenmore Elite Front Loader Washers This fixed my problem exactly! Check that the tab on the washer's door that inserts into the door lock is not broken, that it's properly aligned with the door lock hole, and that there is nothing F27 OVERFLOW CONDITION If the overflow contact on the pressure switch is closed for more than 60 seconds, an Overflow Condition occurs. Whirlpool Washer Something went Wrong: This page should be removed because: It's spam/self promotion It's in the wrong category It's irrelevant It's illegal It's inappropriate/offensive Other Reason: Cancel Report this Page

About

Check the pressure switch. 8. F27 Error Code Kenmore Expand Popular Questions 13 Answers Water overflowing from drain pipe Kenmore Elite 45986 Front Load... 18 Answers F2 error code on my Kenmore Elite HE3 washer Kenmore Elite 45986 Front Load... Replace Central Control Unit if drum is not moving F71 USER INTERFACE HEARTBEAT FAILURE If a Central Control Unit Heartbeat Failure is displayed, no communication is detected from the User Interface If everything else checks out and your problem still persists, you may have a component failure (more commonly, the CCU or pressure switch).I hope this information is found to be helpful

F29 DOOR UNLOCK ERROR If the door unlock has failed 6 times. This should clear the unit of the excess detergent. • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain If corrections are made in any step, reconnect power to control. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 4.

F27 Error Code Kenmore

This code will also appear if the user presses the START key while the lid is open. http://applianceassistant.com/Washer-Repair/Duet-Washer-2nd-Gen/Duet-Washer-Error-Codes.php Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU). Whirlpool Duet F27 Error Code Follow ApplianceAssistant on Twitter! About Appliance Repair Safety Legal Stuff Sponsor a Child => Future Hope Ministries Copyright Appliance Assistant, LLC. 2015 Skip to content Blog Menu Our Website About Whirlpool Front Load Washer Error Codes Verify CCU operation by running a Diagnostic Test or any cycle. 6.

In this case nothing is talking and appears functional components have gone on strike. have a peek at these guys If all that looks good check the drain system for blockages or you may have a bad drain pump. Unplug washer or disconnect power. 2. NOTE: The door switch/lock unit can be manually unlocked. Whirlpool 6th Sense Washing Machine Error Codes

F71 User Interface Heartbeat Failure Error The Duet washer's main control board is unable to connect to the washers user interface. (the control buttons) Check all the connections between the User Look for pinched wire. The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed. http://itechnologysolutionsllc.com/error-code/whirlpool-duet-washer-error-codes-f70.php Ask Your Own Appliance Question Customer: replied6 years ago.

Check the MCU by looking for operations of the drive motor. 6. Overloading the unit may cause this problem. New harness?

Try to reset the Duet washer's memory by unplugging the washer for 2 minutes.

My prime example is an automobile, engine compartment temperatures, and even passenger cabin temperatures can greatly exceed the range of what a typical white good will see, from hot sunny days, F22 DOOR LOCK ERROR After 6 failed attempts to lock the door. Nov 30, 2009 | Whirlpool Duet GHW9150P Front Load Washer 1 Answer F21 Error Code on Whirlpool Duet & Kenmore Elite Front Loader Washers This helped my husband fix our washer. See Details More Products Whirlpool WTW5000DW 4.3 cu.

If there is water in the unit: Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. F30 Dispenser Error The detergent dispenser was not able to reach it's destination. And the truth shall make you free. this content Verify inlet valve operation.

Verify pressure switch operation. 7. Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) Check the MCU Check the Drive Motor Now its the long weekend and no one is open to help me out. The pressure switch is not tripped after 6 minutes.

Follow us