Home > Error Code > Whirlpool Duet Sport Error Code F27

Whirlpool Duet Sport Error Code F27

Contents

Verify the shipping system including shipping bolts, spacers and cables are removed. 2. The failure will be reset after running the Diagnostic Test Program. 1. Mismatch of User Interface and CCU or corrupted EEPROM. 1. My advice for that would be a Mossberg 500. weblink

Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU). Unplug washer or disconnect power. 2. AppliancePartsPros 5,666 views 7:05 Whirlpool duet sport washing machine not draining, codes F05 or F21 showing up - Duration: 10:33. F24 WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of range (23°F to 217°F[-5°C to 103°C]) during the water-heating step of the WASH cycle.

Kenmore F27 Error

Alprazolam 268,941 views 7:21 Whirlpool washing machine drain pump replacement and diagnostic - Duration: 17:45. It is also a good idea to check the drain hose just prior to the drain pump as well. Refer to the Water Temperature Sensor section. Press STOP/CANCEL to clear the display.

  1. Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and b etween the MCU and the Central Control Unit (CCU).
  2. Potential Causes • Check Wire Harness connections to the MCU, the motor, and Central Control Unit (CCU) • Check the Drive system for any worn or failed components • Check MCU
  3. Door switch open while door is locked. 1.
  4. Close Yes, keep it Undo Close This video is unavailable.
  5. Press PAUSE/CANCEL two times to clear the display. 1.
  6. Press CANCEL and observe for 1 minute to ensure operation is correct. 6.
  7. F9 Oven door lock failure Check wiring to door lock switch (the wire harness may be connected wrong).

There should be small filter screens that you can remove and clean/replace. Unplug washer or disconnect power. 3. Sud SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE) If suds are detected continuously by the pressure switch during the drain or spin phases, the washer will fill 4 Whirlpool Washer I have seen the filter clogged and give these type of symptoms but here is error code F27 out of the maintenance manual If the overflow contact on the pressure switch

Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. Potential Causes • Door lock is broken. • Check door lock switch for foreign objects • Check wire harness connections to the door lock switch and the main control board at In an overflow condition, the door remains locked and the drain pump runs constantly, even if PAUSE/CANCEL is pressed twice and the display is cleared. Sign in to make your opinion count.

Make sure the harness does not have a bad connection. • Check the quick disconnect at the motor terminal. Check the MCU by looking for operations of the drive motor. 5. Make sure you drain the water from the drain lines, pump and hoses PRIOR to removing the cover. Door switch/lock unit failure. 1.

Whirlpool Washing Machine Fault Codes

Loading... http://www.appliancehelponline.com/whirlpool.html Unplug washer or disconnect power. 2. Kenmore F27 Error Perform Service Cycle to pair the UI and CCU SW. 2. Whirlpool 6th Sense Washing Machine Error Codes check that all the connections to the main control are fully connected.

Turn off hot and cold water faucets and unplug the unit before servicing. 1. http://itechnologysolutionsllc.com/error-code/whirlpool-duet-sport-error-code-f-27.php Hard to narrow this one down. LinkBack Thread Tools Search this Thread Display Modes #1 (permalink) 03-22-2011, 06:58 PM wilsonpack4 Junior Member Join Date: Mar 2011 Posts: 1 Error Code F27 Model Number: WFW8300SW04Brand: Ft. Whirlpool Duet Dryer Error Codes

Refer to the Water Temperature Sensor section. You have not opened to door for 3 wash cycles… 3. Failure Code LED Status Duet Sport LED Status Duet Sport HT F01 Add a Garment Add a Garment F11 Add a Garment, Wash, Spin Add a Garment, Soak/Prewash, Rinse F20 Rinse, check over here Verify CCU operation by running a Diagnostic Test or any cycle. 3.

Door switch open while door is locked. 1. Plug in washer or reconnect power. 4. Check that the drain pump is working properly. 3.

The failure will be reset after running the Diagnostic Test Program.

Unplug washer or disconnect power. 4. Another possibility; pressure switch or pressure switch hose. Disconnect power for at least 30 seconds. 2. Overloading the unit may cause this problem.

The failure will be reset after running the Diagnostic Test Program.STEAMER DEFECT The Steamer temperature has not reached the correct value. Book says it is a pump motor issue or a CCU issue, motor is not that old so went and bought a new CCU. Capacity, Stainless Steel Wash Basket Best Picks for 2015 ​ Sponsors Troubleshooting Top Load Washer Front Load Washer Electric Dryer Gas Dryer Electric Range Gas Range Refrigerator Microwave Dishwasher View All this content This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds.

Check if the hose is not blocked. It should be approx. 115 Ω. 4. Kenmore Washing Machines impeller loose pump drain pump filter located clean inlet valve filter water fill not running ccu remove error f27 clean filter trap reset ccu drain overflow View Less NOTE: The door switch/lock unit can be manually unlocked.

Check the inlet valve for proper shut off. 7. Run a NORMAL cycle without adding any detergent. Replace CCU board. Replace User Interface if drum is rotating. 4.

Running small loads with the same amount of detergent can also cause an over suds condition. Check door switch/lock unit. 3. Replace User Interface if drum is rotating. 4. Replace CCU board.

F42 MOTOR CONTROL UNIT FAILURE - REPETITIVE UNDERVOLTAGE The Motor Control Unit continuously checks for voltage. NOTE: During first power up of new CCU and UI combination, a bootphase (uploading parameters) will be performed. F7 Function key stuck on ERC Replace control board (also called ERC or clock). Jen Russo 1,622 views 3:20 Girls fix the Whirlpool Duet Steam Code F21 on Xmas Eve! - Duration: 7:35.

Check the drive system for any worn or failed components. 5. Check Pressure Switch harness for continuity. 2. NOTE: During first power up of new CCU and UI combination, a bootphase (uploading parameters) will be performed. F42 MOTOR CONTROL UNIT FAILURE - REPETITIVE UNDERVOLTAGE The Motor Control Unit continuously checks for voltage.

If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way. Sign in to report inappropriate content. Make sure all grounding switches are engaged. 3. Check the drive motor for powered rotations. 6.

Follow us