Home > Error Code > Whirlpool Built-in Electric Oven Error Codes

Whirlpool Built-in Electric Oven Error Codes

Contents

Reach up along the inside of the front panel and locate the bottom of the door latch assembly. 4. Check wire harness connections to the Central Control Unit (CCU) and the dispenser motor. CE Communications error If there is any breakdown in communication between the machine controller and the motor controller, "CE" flashes and the unit beeps once. Replace failed component. weblink

F26 DOOR SWITCH ERROR If the door has not been opened for 3 consecutive cycles or the door switch is open while the door is locked for more than 5 seconds. If the problem persists, replace the electronic oven control. If a potential suds lock is detected, the control tries up to 3 times to clean out the unit with a mini-cycle. "SL" is displayed if suds are detected but the Open and close the door. 2.

Whirlpool Oven Fault Codes

F2-E0 - Shorted Touch Pad (Keypad) - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. We must receive the returned part(s) with the Return Authorization number within 365 days of your original order date. F1 Board failure Replace control board (also called ERC or clock). Check the MCU by looking for operations of the drive motor. 7.

Keypad, Electronic oven control (EOC) F3/E0 CANCEL key is defective Disconnect power or unplug the wall oven. FUSES Many oven temperature-sensing circuits have a fuse. Re-apply power and observe for at least one minute. 3. Whirlpool Oven Error Codes F5 Reconnect the oven temperature sensor wire harness if loose.

To manually check the function of the Pressure Switch, remove hose from switch and apply air to switch. This should have AC line voltage when the motor controller is powered. Tell us how to save your model.

If too much detergent was used: Run the unit through a RINSE/SPIN cycle.

Find Parts Whirlpool Duet Front Loading Automatic Washer Fault Codes Failure Code Fault Code Description Solution FH No water detected entering machine or Pressure switch trip not detected. Whirlpool Top Load Washer Error Codes Gently pull the tab down approximately 1/4 inch or until a 'click' is heard. Verify wire harness connections to inlet valves, pressure switch, drain pump and Central Control Unit (CCU). 5. F06 STEAMER DEFECT The Steamer temperature has not reached the correct value.

Whirlpool Oven Error Codes E2 F3

Check the wire harness connections to the Motor Control Unit, Central Control Unit, and Interference Filter. 3. http://www.appliancerepair.net/oven-repair-7.html Sr - Stuck Relay - The machine control board may have a bad relay and may need to be replaced. Whirlpool Oven Fault Codes If there is no water in the unit: Make sure that both valves at the water source(s) are turned on all the way. Whirlpool Range Error Code F9e0 OK, Continue

If a failure occurs during high-speed spin the door will be unlocked after 3 minutes. have a peek at these guys Potential Causes • Check mechanical linkage from dispenser motor to the top of the dispenser. • Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU) • Check F62 STEAMER ELECTRONIC BOARD RELAYS ERROR One of the steamer relays (K1, K2, K3, K4) on the Steamer Electronic board have failed, there is an open or short circuit. Disconnect power for at least 30 seconds. 2. Whirlpool Washing Machine Error Codes E1

The relay might be soldered or always open. Check for continuity of the User Interface harness. 2. DOUBLE OVENS Most double ovens have two control boards. check over here Or If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the

Verify the shipping system including shipping bolts, spacers and cables are removed. 2. Whirlpool Top Load Washing Machine Error Codes Replace CCU board. Sometimes just simply wiggling a connector may clear up the error code.

Please check back in a few minutes.

  1. Opening the lid will allow you to view and redistribute the load.
  2. Re-apply power and observe for at least one minute. 3.
  3. Press PAUSE/CANCEL two times to clear the display. 1.
  4. Check keypad connector for firm connection (keypad connects to control board). 2.
  5. Unplug washer or disconnect power. 3.
  6. Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU).

Check the MCU by looking for operations of the drive motor. 6. E Turning to "off" stops the error and flashing can tweak away the code. F02 Long Drain If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed. Whirlpool Oven Error Codes E6 F2 All other trademarks are owned by their respective companies.

Measure the oven temperature sensor resistance using a volt/ohm meter. Open and close the oven door to see if the oven door switch turns the oven light on and off when the oven door is opened and closed. F9 - Oven Door Lock Failure - Check door lock switches and wiring. this content Potential Causes • Check the drain hose and make sure it is not plugged or kinked • Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit

The failure will be reset after running the Diagnostic Test Program. 1. Check for drain pump failure. 6. Potential Causes • Check the Water Temperature Sensor, Heating Element and Element Relay • Check connections to the Sensor, Heating Element and Relay Replace failed component. Begin by disconnecting the power to the range and removing the rear panel covering the ERC.

Replace control. Potential Causes • Door Lock Mechanism broken. • Check Door Lock/Switch Assembly for foreign objects • Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU) • Check wire harness connections to the dispenser motor and Central Control Unit (CCU). 4. Sign in Loading...

Plug in washer or reconnect power. 6. Check the drain hose and make sure it is not plugged or kinked. 2. If door latched: A. Refer to the Continuity tests.

Press CANCEL and observe for 1 minute to ensure operation is correct. 2. Note: Unit will attempt to lock itself during this error six times before displaying the error code. Press STOP/CANCEL to clear the display. Potential Causes • Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU) • Check the MCU

Follow us